bueno lo primero es instalar el gnokii en tu fedora
#yum update
#yum -y install gnokii gnokii-smsd
una vez instalados.. procedemos a buscar el archivo de configuracion de gnokki y editardo deacuerdo al modelo de tu celular
para esto debes saber q tipo de cable estas usando.. el mio es un DKU-2 para saber q modelo
http://www.gnokii.org/cables.shtml
en esta direccion pueden ver la lista de cables
una vez eso... a editar el archivo gnokiirc
nano /etc/gnokiirc
alli solo van a cambiar
# This is a sample ~/.gnokiirc file. Copy it into your
# home directory and name it .gnokiirc.
# See http://wiki.gnokii.org/index.php/Config for working examples.
#
[global]
# Set port to the physical port used to connect to your phone.
# Linux version is:
port = 1
#
# For MacOSX you will need something like:
# port = /dev/cu.USA28X1P1.1
#
# For Win32 you want to use:
# port = com1:
# or similiar.
#
# FreeBSD (probably NetBSD and OpenBSD too) use:
# port = /dev/cuaa0
#
# With Linux-IrDA you will want to use
# port = /dev/ircomm0
# or similiar.
#
# Use this setting also for the Bluetooth connection:
# port = aa:bb:cc:dd:ee:ff
# when using it with AT driver set it to:
# port = /dev/rfcomm0
# or similiar.
#
# For the Linux USB cables you will need one of the following settings (or
# similiar)
# port = /dev/ttyUSB0
# port = /dev/tts/USB0
# port = /dev/ttyACM0
# the last one will work only with AT driver. The correct setting should be
# given in the dmesg output.
#
# If you use connection type dku2libusb use it to denote which use endpoint
# you'd wish to use. It is useful when you have more than one phone connected
# to your computer using DKU2 cable. Numbering goes from 1 upwards.
# Default is 1.
# port = 1
# Set model to the model number of your phone. For the
# Symbian phones use:
# model = symbian
# For other non-Nokia phones and when you want to use AT
# mode use:
# model = AT
# If you can't figure out what to put here read the FAQ.
# If it still doesn't help, consult gnokii-ml or #gnokii at freenode.
model = series40
# There are few main models that should make use of the certain drivers.
# These are: 6110, 7110, 6510, 3110, 2110, 6160.
# Set IrDA device name.
# If you use irda connection you may want gnokii to autodetect the irda
# device it connects to. This is fine for most of the cases. if you have
# more than one device in range you may want to give manually the device
# name so gnokii correctly recognizes it. Use the name that you can see
# in the discovery log when the phone with infrared is in the range of
# your irda port.
# Note that you need to set this for each phone_ section separately. It
# isn't nested from the global section.
# irda_string = Nokia 6610i
# Initlength controls the number of characters sent to the
# phone during initialisation. You can either set it to
# the word "default" or a positive integer.
#
# You can try setting this value if you want to connect
# to the phone quicker. If you've never noticed the
# connection to be slow, it is suggested that you
# leave this alone. Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = default
# The type of the connection, for IR set this to infrared or irda.
# For the nk6110 driver only infrared is valid for the IrDA connection.
# See Docs/gnokii-ir-howto for more detailes on this.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
# If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
# you don't use model = AT) you may want to use 'dlr3p' value here.
# Note that it is recommended and currently the best way to use this
# cable with nk6510 driver.
connection = dku2libusb
# With DKU-2 cable use the following setting if you want to libusb driver
# (recommended):
# connection = dku2libusb
# or the following setting if you want to use Linux kernel driver
# connection = dku2
# With DKU-5 cable use the following setting
# connection = dku5
# For Bluetooth and AT driver use the following setting
# connection = serial
# For other Bluetooth settings use
# connection = bluetooth
# For infrared connection with phones other than Nokia 6110/6130/6150 use:
# connection = irda
# Don't forget to run: 'irattach irda0 -s' or similiar before running gnokii
# For connection with a PC/SC compatible Smart Card reader use:
# connection = pcsc
# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = yes
# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
serial_baudrate = 19200
# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"! FIXME: Model-driven autodetection
#serial_write_usleep = 10000
# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3 wires)
#handshake = software
# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1
# If you are using a bluetooth connection, you can specify the rfcomm
# channel number here. Default value is 1.
#rfcomm_channel = 1
# There may happen various timeouts during the communication with the phone.
# This parameter enables the retransmission policy. Ie. if the phone doesn't
# respond, we send the frame again. This happened mainly with the older
# phones. You may want to enable it when you see mysterious timeouts.
# Be very careful with this option. It is suspected to cause phone breakage
# with new DCT4 phones (like Nokia 6100). By default it is switched off
# (sm_retry = 0)
#sm_retry = 1
# Run the specified script(s) right after opening and initializing the device
# and before any communication (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is run!
#connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
#disconnect_script =
# When sending SMS you can experience timeouts. This is the feature of the
# overloaded SMSCs. The phones waits for the response from the SMSC confirming
# that it received the short message. When the SMSC is DoSed with many requests
# it will take more time to get the response. Adjust it to your needs. The
# value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to wait
# forever.
smsc_timeout = 10
# Set this to 1 if you want to break your phone with xgnokii. Works only
# with few Nokia models and FBUS communication
[xgnokii]
allow_breakage = 0
# Set bindir to point to the location of the various gnokiid binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii. Ensure you
# are in the gnokii group and that the group exists...
[gnokiid]
bindir = /usr/sbin/
# Any entries in the following two sections will be set as environment
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(8) script.
[connect_script]
TELEPHONE = 12345678
[disconnect_script]
# The following parameters control how libgnokii handles the debugging messages.
# Currently there are three categories: "debug" controls the libgnokii
# normal debug output, "rlpdebug" controls the debug output of the RLP
# subsystem, and "xdebug" is used by the xgnokii or smsd.
[logging]
# where to log the debug output (on: stderr, off: /dev/null)
debug = off
# where to log the rlp debug output (on: stderr, off: /dev/null)
rlpdebug = off
# where to log X debug output (on: stderr, off: /dev/null)
xdebug = off
En el wiki la configuracion viene asi (es la misma configuracion que un DKE-2, lo que pasa es que uno es Mini-USB y el del nuevo Nokia es Micro-USB pero el funcionamiento es el mismo:
[global]
model = series40
port = 1
connection = dku2libusb
guardan
salen
ahora desde consola pueden hacer una prueba de conexion con el gnokii
[rperez@FreeDOM ~]$ gnokii --identify
GNOKII Version 0.6.27
LOG: debug mask is 0x1
Config read from file /etc/gnokiirc.
phone instance config:
model = series40
port = 1
connection = dku2libusb
initlength = default
serial_baudrate = 19200
serial_write_usleep = -1
handshake = software
require_dcd = 0
smsc_timeout = 10
rfcomm_channel = 0
sm_retry = 0
Connecting
Serial device: opening device USB
Ignoring extra header, type 171, length 5
Found FBUS interface
Can't set configuration: -16
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 07 01 00 |
Message received: 0x1b / 0x004a
01 2e 00 08 01 03 6a 30 00 2c 56 20 30 36 2e 34 | . j0 ,V 06.4
31 2e 33 2e 30 0a 32 34 2d 31 30 2d 32 30 30 36 | 1.3.0 24-10-2006
0a 52 4d 2d 31 37 30 20 31 32 34 0a 28 63 29 20 | RM-170 124 (c)
4e 6f 6b 69 61 00 6e 08 00 04 32 35 36 00 70 0c | Nokia n 256 p
00 05 31 30 32 38 00 00 00 00 | 1028
Received message type 1b
model length: 10
Received model RM-170 124
Identifying...
Message sent: 0x1b / 0x0005
00 01 00 00 41 | A
Message sent: 0x1b / 0x0006
00 01 00 07 01 00 |
Message received: 0x1b / 0x001a
01 2e 00 01 00 01 41 14 00 10 33 35 31 38 39 32 | . A 35XXXX
30 31 37 34 31 39 38 37 35 00 | XXXXXXXXX
Received message type 1b
Received imei 35XXXXXXXXXXXX
Message received: 0x1b / 0x004a
01 2e 00 08 01 03 6a 30 00 2c 56 20 30 36 2e 34 | . j0 ,V 06.4
31 2e 33 2e 30 0a 32 34 2d 31 30 2d 32 30 30 36 | 1.3.0 24-10-2006
0a 52 4d 2d 31 37 30 20 31 32 34 0a 28 63 29 20 | RM-170 124 (c)
4e 6f 6b 69 61 00 6e 08 00 04 32 35 36 00 70 0c | Nokia n 256 p
00 05 31 30 32 38 00 00 00 00 | 1028
Received message type 1b
Received revision V 06.41.3.0
model length: 10
Received model RM-170 124
IMEI : 35XXXXXXXXXXX
Manufacturer : Nokia
Model : RM-170 124
Product name : RM-170 124
Revision : V 06.41.3.0
Serial device: closing device
y asi ya tienen el celular configurado en gnokii.. ahora pueden usar el cell desde su fedora.. ya sea para llamar.. enviar sms..
hasta el siguiente capitulo!
No hay comentarios:
Publicar un comentario